[Jan 07, 2025] New Updated D-PEMX-DY-23 Exam Questions 2025
Updated Free EMC D-PEMX-DY-23 Test Engine Questions with 138 Q&As
NEW QUESTION # 13
An MX7000 administrator has been tasked to perform the initial configuration of a new MX platform.
The MX700 has seven MX740c, one MX5016s, two Management Modules (MMs), an LED-Only control panel, two MX9116n in Fabric A, two MX5108n in Fabric B, and two MX5000s in Fabric C.
What is a valid method to perform the initial MX platform configuration?
- A. Use Ethernet front panel port default DHCP address
- B. Use QuickSync 2
- C. Use a serial DB9 / DB cable
- D. Use KVM and racadm setniccfg command from MM configuration menu
Answer: D
NEW QUESTION # 14
What is the number of server-facing ports and the bandwidth of each port on the MXG610s?
(Choose two.)
- A. 8x 32 Gbps
- B. 8x 16 Gbps
- C. 16x 16 Gbps
- D. 16x 32 Gbps
Answer: C,D
NEW QUESTION # 15
What are two considerations when adding an MX760c in a chassis running OME-M firmware earlier than v2.0?
(Select 2)
- A. If the MX760c is a thermally challenged system, the maximum supported ambient temperature cannot be reduced.
- B. If the MX760c is not a thermally challenged system, the sled is going to run as designed.
- C. If the iDRAC of the existing sleds is not at a supported level, ATMOS cannot calculate the maximum cooling.
- D. All the fans on the PowerEdge MX7000 must be Silver Grade.
Answer: A,C
NEW QUESTION # 16
What is a function of the Fabric Resources Director (FReD)?
- A. Providing QuickSync 2 feature
- B. Hosting OME-M interface
- C. Critical temperature monitoring
- D. SAS Expander routing for Fabric C
Answer: C
NEW QUESTION # 17
What does OBPAR allow on a PowerEdge MX750c?
- A. Boot a compute sled with only one CPU.
- B. Run a compute sled with memory overclocking.
- C. Boot a compute sled with reduced frequency.
- D. Run a compute sled with maximum performance.
Answer: C
NEW QUESTION # 18
What configuration is supported for a fully populated MX740c compute sled?
- A. 1 Fabric A mezz card 1 Fabric B mezz card
1 Fabric C mini-mezz card - B. 1 Fabric B mezz card
1 Fabric C mezz card with Fabric A being integrated into the system board - C. 2 Fabric A mezz cards 2 Fabric B mezz cards
2 Fabric C mini-mezz cards - D. 1 Fabric A mezz card
1 Fabric B mezz card with Fabric C being integrated into the system board
Answer: A
NEW QUESTION # 19
On which generation of server was the BOSS-N1 controller introduced?
- A. 16G
- B. 15G
- C. 14G
Answer: A
NEW QUESTION # 20
A technician replaces a failed Management Module in an MX7000 chassis group. After the technician leaves the site, the administrator reports that the lead chassis is no longer able to communicate with its members.
How can OME-M be used to confirm the cabling configuration?
- A. View the topology map from the Group Lead
- B. View the health status of the lead Chassis Management Module
- C. View the I/O module topology map from the lead chassis
- D. View the health status of the lead Chassis Management ports
Answer: D
NEW QUESTION # 21
What can be used as the firmware update source for OME-M within an MX chassis?
- A. Dell Update package
System Live Image (SLI) - B. Dell Update Package
Baseline from a Catalog - C. Server Update Utility
Baseline from a Catalog - D. Server Update Utility
System Live Image (SLI)
Answer: B
NEW QUESTION # 22
An administrator has installed the iDRAC Service Module in the OS on a compute sled, they are unable to use its features in the iDRAC web GUI.
What is the likely cause of this issue?
- A. OS to iDRAC pass-through feature is not enabled in the iDRAC
- B. Installed OS is not supported
- C. iDRAC Express license is installed
- D. OS and iDRAC are configured on different networks
Answer: A
NEW QUESTION # 23
A technician has replaced an MX chassis tub. They complete the tub installation and power on the chassis. They notice that the KVM is no longer functional.
What should the technician do after confirming the KVM feature is still enabled in OME-M?
- A. Ensure all installed Management Modules are connected to the network
- B. Ensure all cables connecting the tub to the left ear control panel are connected properly
- C. Ensure all cables connecting the tub to the right ear control panel are connected properly
- D. Ensure all power supplies are connected and powered-on
Answer: B
NEW QUESTION # 24
An implementation engineer prepares to install a PowerEdge MX7000.
Which serial cable do they use?
- A. DB9 --> DB9
- B. USB-A --> USB-B
- C. DB9 --> Micro DB9
- D. USB-A --> Micro USB-B
Answer: D
NEW QUESTION # 25
Which statement describes L2 Multicast as implemented on the PowerEdge MX7000 IOM?
- A. MLD snooping controls the flooding of IPv4 multicast traffic on VLANs while the IGMP limits the flooding of IPv6 multicast traffic.
- B. MLD snooping and IGMP control or limit the flooding of IPv4 multicast traffic on VLANs.
- C. MLD snooping and IGMP control or limit the flooding of IPv6 multicast traffic on VLANs.
- D. MLD snooping controls the flooding of IPv6 multicast traffic on VLANs while the IGMP limits the flooding of IPv4 multicast traffic.
Answer: D
NEW QUESTION # 26
Which two main components comprise a Scalable Fabric?
- A. MX9116n and the MX5108n
- B. MX9116n and the 25GbE PTM
- C. MX9116n and the MX7116n
- D. MX7116n and the MX5108n
Answer: C
NEW QUESTION # 27
In an MX7000, which components are cooled by the rear fans?
- A. Fabric A, B, and C IOMs only
- B. Management Modules only
- C. Fabric A, B, and C IOMs and the Management Modules
- D. All compute and storage sleds
Answer: C
NEW QUESTION # 28
A customer has an MCM group consisting of four MX7000 chassis. They need to take the lead chassis down to perform maintenance.
How can the customer ensure that another chassis takes over the lead role in the MCM Group?
- A. The MCM group will elect a new lead chassis.
- B. Promote the backup lead chassis as the new lead chassis.
- C. Promote the lead chassis to a passive chassis.
- D. The backup chassis will take the lead automatically.
Answer: B
NEW QUESTION # 29
What component enables the MX840c compute sled to have this configuration?
4 x CPUs
4 x mezzanine cards
2 x mini mezzanine cards
48 DDR4 DIMM slot
- A. processor expansion module
- B. mezzanine expansion module
- C. motherboard expansion module
- D. memory expansion module
Answer: A
NEW QUESTION # 30
Where in the OME-M Web interface can the Chassis Deployment Wizard be found?
- A. Configuration > Deploy > Chassis Deployment Wizard
- B. Hardware > Initial Configuration
- C. Home > Settings > Chassis Deployment Wizard
- D. Home > Configure > Initial Configuration
Answer: D
NEW QUESTION # 31
Which protocol(s) does Redfish use?
- A. JSON and OData only
- B. OData only
- C. JSON only
- D. JSON, OData, and SNMP
Answer: A
NEW QUESTION # 32
What is a characteristic of MX7000 networking in Scalable Fabric Mode?
- A. All switch interfaces are assigned to VLAN 1 by default and are in the same Layer 2 bridge domain.
- B. Available on MX9116n FSE and MX7116n FEM but not on the MX5108n.
- C. Layer 2 bridging is disabled be default and interfaces must join a bridge domain (VLAN) before being to forward frames.
- D. Enabled by default, all switch-specific OS10EE capabilities are available.
Answer: B
NEW QUESTION # 33
A server administrator is deploying a VMware vSphere cluster and configuring High Availability on a PowerEdge MX7000 modular system.
Which configuration is required?
- A. SAS IOM setup in redundant mode
- B. Enclosure-assigned storage
- C. PERC MX745P
- D. Drive-assigned storage
Answer: B
NEW QUESTION # 34
......
Try 100% Updated D-PEMX-DY-23 Exam Questions [2025]: https://passleader.bootcamppdf.com/D-PEMX-DY-23-exam-actual-tests.html