NACE NACE-CIP1-001 Exam Dumps - PDF Questions and Testing Engine
Latest NACE-CIP1-001 Exam Dumps for Pass Guaranteed
To sit for the NACE-CIP1-001 Exam, individuals must meet certain prerequisites. They must have a minimum of six months of experience in the coatings industry or a related field. They must also have completed a NACE-approved training course or have a certain level of education and experience in the field. Overall, the NACE-CIP1-001 Exam is a challenging but rewarding certification that opens many doors to individuals in the coatings industry.
NEW QUESTION # 44
Removal of welds splatter is required:
- A. When NACE/SSPC abrasive blast standards are specified
- B. When ISO abrasive blast standards are specified
- C. On every job
- D. When specifically identified in the owner's specification
Answer: D
NEW QUESTION # 45
NACE No. 4/SSPC-SP-7 is a joint standard for
- A. white metal blast cleaning.
- B. brush-off blast cleaning.
- C. commercial blast cleaning.
- D. near-white metal blast cleaning.
Answer: B
NEW QUESTION # 46
A NACE Coating Inspector is permitted to transport coating material when:
- A. Asked to do so by the Coating Application team
- B. If the Inspector meets all the necessary requirements for Transportation of Dangerous Goods
- C. The Inspector should never transport coating material
- D. Asked to do so by the Owner's Representative
Answer: C
NEW QUESTION # 47
NACE Level 1 Inspectors have been trained to perform:
- A. Visual inspection and Non-destructive testing
- B. All types of inspection
- C. Visual inspection, Non-Destructive and Destructive testing
- D. Visual inspection only
Answer: A
NEW QUESTION # 48
If a Thermoset coating is heated it will:
- A. Soften when heated and return to its original hardness when cooled
- B. Harden and return to its original hardness when cooled
- C. Harden and retain its hardness when cooled
- D. Soften when heated and retain its softness when cooled
Answer: C
NEW QUESTION # 49
Due to a previous premature coating failure the owner has required the original coating applicator to return to remove and replace 10,000 square feet of a failed three coat system at the applicator's cost. Due to the financial implications of another failure, the owner has offered you the job as the NACE CIP Level 1 Coating Inspector and explained that he expects you to be his "insurance policy" for this job. You have never been involved in a warranty job before and are unfamiliar with the coating system.
Your preferred FIRST course of action is to:
- A. Review the Product Data Sheets and meet with the Coating Applicator 'prior to the pre-job meeting
- B. Meet with the owner and explain your limitations and concerns prior accepting the assignment
- C. Review the Product Data Sheets, and conduct a walk thru of the job site prior to the pre-job Conference
- D. Purchase Professional Liability Insurance prior to job commencement
Answer: C
NEW QUESTION # 50
When performing tests for oil and grease using an ultra-violet light, the NACE Inspector should be aware that:
- A. Chloride salt may produce a false positive
- B. Presence of weld spatter may produce a false positive
- C. Ultra-Violet light may contaminant the surface
- D. Synthetic oil or grease may not be identified
Answer: D
NEW QUESTION # 51
The primary difference between Non-Convertible vs. Convertible coatings is:
- A. Convertible coatings cure solely by solvent evaporation whereas Non-Convertible coatings do not
- B. Convertible coatings do not undergo a chemical change during curing whereas Non-Convertible coatings do
- C. Non-Convertible coatings cure by co-reaction whereas Convertible coatings do not
- D. Non-convertible coatings do not undergo a chemical change during curing whereas Convertible coatings do
Answer: D
NEW QUESTION # 52
When the joint NACE/SSPC abrasive blast cleaning standards are specified, the pictures in SSPC VIS 1 can be used as:
- A. Pass/fail criteria
- B. A final conflict resolution method
- C. A method to grade surface profile
- D. A general guide
Answer: D
NEW QUESTION # 53
ISO SA 2 is defined as:
- A. Thorough Blast Cleaning
- B. Light Blast Cleaning
- C. Very Thorough Blast Cleaning
- D. Near White Metal Blasting
Answer: A
NEW QUESTION # 54
The Inspector's Log Book is generally:
- A. Shredded by the inspector upon project completion
- B. Submitted to the client upon project completion
- C. Retained by the inspector upon project completion
- D. Shared with all parties upon project completion
Answer: C
NEW QUESTION # 55
If inspectors identify issues of non-conformance during an inspection, they should
- A. instruct the contractor's personnel in how to correct the issue so the project is not delayed
- B. perform additional tests secretly to ensure there are no other potential issues at the site
- C. inform both the Contractor and the inspector's supervisor so they can take appropriate corrective actions
- D. wait until the final report is being prepared to identify the issues in writing so they are fully documented
Answer: C
NEW QUESTION # 56
Using SSPC Vis 1 as a guide when performing a visual inspection of a steel surface prior to surface preparation a NACE Inspector would assign which designations to the surface condition:
- A. Surface Condition H
- B. Surface Conditions E-G
- C. Rust Grades 1-4
- D. Rust Grades A-D
Answer: D
NEW QUESTION # 57
You are the NACE Inspector on a tank lining project where a 50% solids epoxy tank lining is being applied. After application of the 19 coat you notice small blisters in some areas of the applied lining.
Your FIRST preferred course of action is to:
- A. Break the blisters to see what's inside
- B. Document the problem and advise the Contractor and Owner's representative
- C. Extract any liquid that may be inside the blister and send it to the lab for further analysis
- D. Document the problem and advise the Contractor
Answer: B
NEW QUESTION # 58
Which is a component that supplies most of the features and functions of the material?
- A. binder
- B. additive
- C. pigment
- D. solvent
Answer: A
NEW QUESTION # 59
An exposed area of the substrate or previous coat of a conductive coating material, often caused by poor application technique is called
- A. cracking.
- B. holiday.
- C. sagging.
- D. checking.
Answer: B
NEW QUESTION # 60
Most industrial coatings are:
- A. Resistant to temperatures above 200C
- B. Resistant to concentrated sulfuric acid
- C. Inorganic
- D. Organic
Answer: D
NEW QUESTION # 61
Relative humidity is
- A. the lowest temperature at which moisture forms on a steel surface.
- B. the highest temperature at which moisture forms on a steel surface.
- C. a measure of the amount of moisture in the air compared to saturation level.
- D. a measure of the amount of moisture in the air compared to the air temperature.
Answer: C
NEW QUESTION # 62
Solvents are added to coating formulations to
- A. decrease film permeability.
- B. provide color.
- C. increase film permeability.
- D. dissolve binders and form liquid coatings.
Answer: D
NEW QUESTION # 63
As a NACE Coating Inspector your responsibility with respect to safety is to:
- A. Check the credentials of the Safety Officer on site
- B. Act in accordance with the site safety requirements and set an example
- C. Assume the role of the Safety Inspector
- D. Check the PPE used by the Applicators
Answer: B
NEW QUESTION # 64
Surface profile describes:
- A. The level of surface roughness required after abrasive blasting
- B. The general condition of the surface required after abrasive blasting
- C. The initial condition of the surface prior to abrasive blasting
- D. The level of surface cleanliness required after abrasive blasting
Answer: A
NEW QUESTION # 65
You have just received your NACE CIP Level 1 certification when you are asked to supervise a team of uncertified field pipeline inspectors.
Your FIRST preferred course of action is to:
- A. Accept the assignment without hesitation
- B. Meet with the prospective employer to determine the scope of your role
- C. Review the NACE Attestation prior to making a decision
- D. Advise the prospective employer that you cannot accept the position
Answer: B
NEW QUESTION # 66
ISO SA 2.5 is defined as:
- A. Thorough Blast Cleaning
- B. Very Thorough Blast Cleaning
- C. Light Blast Cleaning
- D. Near White Metal Blasting
Answer: B
NEW QUESTION # 67
......
Reliable CIP Level 1 NACE-CIP1-001 Dumps PDF Dec 14, 2023 Recently Updated Questions: https://passleader.bootcamppdf.com/NACE-CIP1-001-exam-actual-tests.html